Cumulus Hanging

Bobbien333 · **Posted:** Sun Apr 22, 2012 12:35 pm

Everything was good for a long time until this morning. I looked and it didn't update. So, I closed it down, went to restart and it just hangs. I restarted the computer and tried again, same thing.
Went to the cumulus site and seen there was an update, so I updated it. I installed the update and it still hangs.
I don't know what else to do. I cleaned everything out on the computer temp, and all.
This is a pick of what just sits there.

steve · **Posted:** Sun Apr 22, 2012 12:56 pm

You may well have the same problem that a number of Fine Offset users have; the station just stops responding. I'm afraid I have no idea why it happens, or whether it's anything to do with Cumulus (but it seems to happen with other software too). A reset should get it going again.

Bobbien333 · **Posted:** Mon Apr 23, 2012 12:09 am

I did a reset and it is working, but I have to put in all my internet info and passwords lol.
Thanks Steve.

Barb

steve · **Posted:** Mon Apr 23, 2012 7:35 am

You should only have needed to reset the station, that doesn't affect any Cumulus settings at all.

Ricardo · **Posted:** Tue May 08, 2012 8:31 am

Hello.

I had the same problem here. The program gives a error for the station readings.
Maybe it is possible that the software can restart by itself for example every 24 hours, then the connection is remade and will work again.

Ricardo Wessels

steve · **Posted:** Tue May 08, 2012 8:38 am

Ricardo wrote:

I had the same problem here.

Not the same problem; you have a different type of station.

Quote:

The program gives a error for the station readings.

What's the exact error message?

Quote:

Maybe it is possible that the software can restart by itself for example every 24 hours, then the connection is remade and will work again.

There's the option to restart if data stops; but I can't tell whether that will help in your situation until I know what your problem is.

Ricardo · **Posted:** Tue May 08, 2012 10:44 am

Hello.

The program gives the red error light but i can't find any error reason. I found the restart option you mentioned and activated it.

When i know more about the error message i come back to it.

Ricardo.

steve · **Posted:** Tue May 08, 2012 10:54 am

Ricardo wrote:

The program gives the red error light but i can't find any error reason.

What error is shown when you click on the red error light?

Ricardo · **Posted:** Tue May 08, 2012 11:25 am

steve wrote:

Ricardo wrote:

The program gives the red error light but i can't find any error reason.

What error is shown when you click on the red error light?

I already restarted the program. When the error occurs again i can check the error reason.

Ricardo

Bobbien333 · **Posted:** Sat May 12, 2012 12:15 pm

It is doing it again. I reset, and this time it didn't work. I changed the batteries and now it is working again. Didn't know if this would help or not.

steve · **Posted:** Sat May 12, 2012 12:50 pm

Was that the batteries in the console, or in the transmitter, Bobbie?

Bobbien333 · **Posted:** Sat May 12, 2012 1:02 pm

Hi Steve,
I replaced the batteries in the console.

faa440 · **Posted:** Thu Jun 21, 2012 4:17 pm

For what it's worth, the hanging occurred once in the past 4 months to my Weatherwise, WS1090 (Fine Offset). After systematically troubleshooting from the software/PC end, the problem didn't clear until after pulling and reinstalling the batteries in the console. Glad I didn't have to climb the pole to get to the transmitter batteries.

atb · **Posted:** Mon Jun 25, 2012 8:25 am

Bobbien333 wrote:

Everything was good for a long time until this morning. I looked and it didn't update. So, I closed it down, went to restart and it just hangs. I restarted the computer and tried again, same thing.

My Fine Offset appeared to do the same thing, after running for ages. It's on 24/7, using an old, dedicated laptop. So, after seeing this thread, I thought I would try something slightly different - a PC restart but also removed the USB cable briefly whilst it was rebooting. On reloading Cumulus (done as a Startup prog) the missing readings were automatically downloaded and processed and all seems OK, without any reset.
Note: No Red light error was shown, Cumulus was just stuck with a blank downloading data window.

steve · **Posted:** Mon Jun 25, 2012 8:32 am

atb wrote:

My Fine Offset appeared to do the same thing, after running for ages.

If you zip up the diags folder and attach it, I may be able to see why it was apparently unable to download the data from the station.

	It is currently Sat May 25, 2013 10:16 am
Please click here before posting. Help me to help you!
Useful Links: Cumulus FAQ • Enhancement requests • Wiki (documentation)
Please put your approximate location into your profile
Add your web site to the Cumulus user map
Vantage Pro2 users with firmware 3.00 should upgrade to fw 3.12 and Cumulus 1.9.4
Latest Cumulus release v1.9.3 (build 1059) - Feb 09 2013 Latest Cumulus beta v1.9.4 build 1078 - May 24 2013 --> Latest Cumulus Realtime v1.0.0.5 - Sep 05 2009

Sandaysoft

Cumulus Hanging

Who is online