Please read the posts in the Announcements section about the current status of Cumulus development now that I have retired

Please read this post before posting

Latest Cumulus release v1.9.4 (build 1099) - Nov 28 2014
Latest Cumulus MX release - v3.0.0 build 3043 Jan 20 2017. See this post for download

[SOLVED] Oregon Scientific WMR88 > ISSUE

Discussion of version 3 of Cumulus, which runs on Windows, Linux, and OS X. All Cumulus MX queries in here, please.
ralph77
Posts: 8
Joined: Fri Jan 06, 2017 4:14 pm
Weather Station: Oregon Scientifics WMR88
Operating System: Windows 10

[SOLVED] Oregon Scientific WMR88 > ISSUE

Postby ralph77 » Thu Oct 26, 2017 6:21 pm

Hi Members.
I face a problem using my Oregon WMR 88 + Raspberry Pi Model B+.

A short timeline event in order to understand the background.
- JANUARY 2017: I succesfully installed my meteo system composed by WMR 88 + RasPi (Jessie Raspbian OS);
- JAN 2017 - OCT 2017: The meteo system was active without any issue.
- Last week I decided to change the Rapi SD Card in order to increase the Disk space so I've performed a "clean installation" using Rasbian Stratch OS.
I have followed the same steps used for the first installation (JAN 2017) but my cumulusMX SW shown only O values (temperature, pressure, etc).

What I've tried:
- re-install OS and Cumulus -> without success
- change in the Station Setting menu of CumulusMX the serial port name from COM0 to /dev/ttyUSB0, /dev/ttyUSB1,.... (the lsusb command show me that Raspi see my WMR)

What I see:
- Last station update is always 00:00:00
- In CumulusMX status the ProcessID (PID) of CumulusMX is always blank.

Thank you very much for your support.

Raffaele.
Last edited by ralph77 on Sat Oct 28, 2017 9:23 am, edited 1 time in total.

User avatar
steve
Cumulus Author
Posts: 26554
Joined: Mon Jun 02, 2008 6:49 pm
Weather Station: None
Operating System: None
Location: Vienne, France
Contact:

Re: Oregon Scientific WMR88 > ISSUE

Postby steve » Thu Oct 26, 2017 6:29 pm

The COM port setting is irrelevant for a USB station. Of more relevance is the version of a Mono that you are using - see the MX FAQ and many posts in the forum about this. It is likely that the version of Mono you are using does not work with the USB library which Cumulus uses.
Steve
-----
Hosting available for Cumulus web sites. See http://sandaysoft.com/forum/viewtopic.php?f=2&t=11876

Please read the posts in the Announcements section about the current status of Cumulus development since I have retired from my day job

ralph77
Posts: 8
Joined: Fri Jan 06, 2017 4:14 pm
Weather Station: Oregon Scientifics WMR88
Operating System: Windows 10

Re: Oregon Scientific WMR88 > ISSUE

Postby ralph77 » Thu Oct 26, 2017 6:55 pm

Thank you Steve!!!
One advice from you: re-install OS+Cumulus or downgrade mono?

Thank you.

User avatar
steve
Cumulus Author
Posts: 26554
Joined: Mon Jun 02, 2008 6:49 pm
Weather Station: None
Operating System: None
Location: Vienne, France
Contact:

Re: Oregon Scientific WMR88 > ISSUE

Postby steve » Thu Oct 26, 2017 7:06 pm

I think that using an older OS with an older Mono would probably be easier than trying to downgrade Mono - from what I read, most people seem to have trouble downgrading Mono.
Steve
-----
Hosting available for Cumulus web sites. See http://sandaysoft.com/forum/viewtopic.php?f=2&t=11876

Please read the posts in the Announcements section about the current status of Cumulus development since I have retired from my day job

ralph77
Posts: 8
Joined: Fri Jan 06, 2017 4:14 pm
Weather Station: Oregon Scientifics WMR88
Operating System: Windows 10

Re: Oregon Scientific WMR88 > ISSUE

Postby ralph77 » Sat Oct 28, 2017 9:22 am

Hi Steve.
Now the issue is solved: my meteo station works fine!

Corrective action applied:
- Raspbian OS (Jessie)
- Mono-complete version 3.2.8.
instead of:
- Raspbian OS (Stratch)
- Mono-complete version 4.x.x

Thank you again.

iz0dpp
Posts: 2
Joined: Wed Jan 23, 2013 1:56 pm
Weather Station: wmr-88
Operating System: windows xp and Raspbian Jessie
Location: jn62go

Re: [SOLVED] Oregon Scientific WMR88 > ISSUE

Postby iz0dpp » Tue Dec 12, 2017 10:23 am

Hi Ralph, Steve
I have your same situation, CMX on Raspberry pi3 with oregon wmr88

I can see on http://localhost:8998 the data, but i cannot upload the standard web files on web space, CMX upload only realtime.txt and realtimegauges.txt
I have try to upgrade and downgrade mono, copy again CumulusMX folder clean, but i cannot see what is wrong

other problem is in the graph section (localhost:8998), don't appear the Temperature curves

anyone can help me to solve this problem?
thank you
Fabrizio.
You do not have the required permissions to view the files attached to this post.


Return to “Cumulus MX”

Who is online

Users browsing this forum: No registered users and 3 guests