I have a problem,most temperature sensors use the standard 2wire pin head thermistor which I can calibrate with a resistor for correct temp readings.But in my WH 1081 sensors they don't use them,but I see IC about 8 pins that must have a thermistor built in,Can any of you electronics buffs tell me if this is true or not.I do like to try different thermistors now and then .
I just wander if you can calibrate these ICs. Thanks John.
Welcome to the Cumulus Support forum.
Latest Cumulus MX V4 release 4.0.0 (build 4022) - 11 May 2024
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Latest Cumulus MX V4 release 4.0.0 (build 4022) - 11 May 2024
Latest Cumulus MX V3 release 3.28.6 (build 3283) - 21 March 2024
Legacy Cumulus 1 release 1.9.4 (build 1099) - 28 November 2014
(a patch is available for 1.9.4 build 1099 that extends the date range of drop-down menus to 2030)
Download the Software (Cumulus MX / Cumulus 1 and other related items) from the Wiki
Temperature sensor thermistors
-
- Posts: 7
- Joined: Thu 17 Sep 2015 1:53 pm
- Weather Station: Ventus W820
- Operating System: Apple I pad
- Location: Eastbourne UK
-
- Posts: 1125
- Joined: Sat 26 Feb 2011 1:58 pm
- Weather Station: Fine Offset 1080/1 & 3080
- Operating System: Windows XP SP3
- Location: SE London
Re: Temperature sensor thermistors
Hi John,
The temperature sensing in Integrated Circuits normally uses the (quite small) fall in the forward voltage drop of a semiconductor diode, which is almost perfectly linear with temperature increases and generally gives better overall accuracy. But the temperature generally needs to be "calibrated" either within the package at manufacture (a memory "lookup" or perhaps "laser trimming", etc.), or subsequently by the main system microcontroller.
AFAIK, the temperature sensing in the "later" FO sensors is now done within the Humidity sensor module and passed to the main microcontroller via a data bus. So the only way to calibrate it would be to intercept the (serial) data and modify it, or to "hack" the main microcontroller (probably impossible in practice).
Cheers, Alan.
Not really; a "thermistor" is normally considered to be a "NTC" resistor which changes its resistance (downwards as the temperature rises) by quite large amounts. However, the change is not linear so the resistance value normally needs additional mathematical calculations to give even a moderate accuracy over the temperature range.John Timson wrote:I see IC about 8 pins that must have a thermistor built in,
The temperature sensing in Integrated Circuits normally uses the (quite small) fall in the forward voltage drop of a semiconductor diode, which is almost perfectly linear with temperature increases and generally gives better overall accuracy. But the temperature generally needs to be "calibrated" either within the package at manufacture (a memory "lookup" or perhaps "laser trimming", etc.), or subsequently by the main system microcontroller.
AFAIK, the temperature sensing in the "later" FO sensors is now done within the Humidity sensor module and passed to the main microcontroller via a data bus. So the only way to calibrate it would be to intercept the (serial) data and modify it, or to "hack" the main microcontroller (probably impossible in practice).
Cheers, Alan.
-
- Posts: 7
- Joined: Thu 17 Sep 2015 1:53 pm
- Weather Station: Ventus W820
- Operating System: Apple I pad
- Location: Eastbourne UK
Re: Temperature sensor thermistors
Thanks for the info Alan.On the Maplins HP1000 station I could correct the sensor readings on the display unit.Thanks John.