La-Crosse WS2300 - Optimal Settings

6719jason · **Posted:** Wed Feb 09, 2011 8:34 pm

Hello Steve & Forum,

I am pleased to say that the replacement for the Watson W8681 arrived yesterday and the new La Crosse WS2300 is now in service.

Setup was a breeze and build quality in my opinion was much improved. Much studier fixtures, fittings and sensors which make me wish it had been replaced sooner.

Quick run through of the setup....

Mains Powered with batteries installed in Console & Transmitter (incase of power failure), Connection between transmitter and console is cabelled which brings the interval to every 8 seconds. Connected to a Real Serial Port via standard RJ11 to Serial connection cable (Included).

Bearing in mind I used a Watson / Fine Offset Station before, I have since changed the settings to what I hope are the optimal settings.

A second, third or fourth opinion would be much appreciated

Attachment:

Screenshot-Cumulus-Settings.png

GraemeT · **Posted:** Wed Feb 09, 2011 10:09 pm

Yep, that's pretty much how my 2355 is set up.

6719jason · **Posted:** Thu Feb 10, 2011 12:16 pm

GraemeT wrote:

Yep, that's pretty much how my 2355 is set up.

Great - Does anyone know the value in mm per tip?

steve · **Posted:** Thu Feb 10, 2011 12:46 pm

6719jason wrote:

:D Great - Does anyone know the value in mm per tip?

0.518 mm.

6719jason · **Posted:** Thu Feb 10, 2011 12:53 pm

Thanks Steve

I trust all my settings from what you can see are correct?

steve · **Posted:** Thu Feb 10, 2011 1:32 pm

Looks OK to me.

Stephenwx82 · **Posted:** Tue Mar 01, 2011 12:38 pm

Hi all I'm a newbie on here, old wx and pc nerd.

Just on an optimal settings for WS2300 series topic, what spike filtering settings are people using for this family of stations?

Vathek · **Posted:** Thu Mar 03, 2011 7:14 pm

Stephenwx82 wrote:

Hi all I'm a newbie on here, old wx and pc nerd.

Just on an optimal settings for WS2300 series topic, what spike filtering settings are people using for this family of stations?

At the moment I'm using 15°C spike removal for temperature and it works fine, the only problem is the dew point which is not filtered, probably because cumulus get it from the station so it would be nice to apply the temperature spike removal setting to the dew point too...

steve · **Posted:** Thu Mar 03, 2011 7:32 pm

Vathek wrote:

At the moment I'm using 15°C spike removal for temperature and it works fine, the only problem is the dew point which is not filtered, probably because cumulus get it from the station so it would be nice to apply the temperature spike removal setting to the dew point too...

You could turn on the option to have Cumulus calculate the dew point, then the temperature spike removal would apply to that too.

Vathek · **Posted:** Fri Mar 04, 2011 8:13 am

steve wrote:

Vathek wrote:

At the moment I'm using 15°C spike removal for temperature and it works fine, the only problem is the dew point which is not filtered, probably because cumulus get it from the station so it would be nice to apply the temperature spike removal setting to the dew point too...

You could turn on the option to have Cumulus calculate the dew point, then the temperature spike removal would apply to that too.

Ok, what is the difference between the dew point calculated from the station or from cumulus? Are there known differences between the two conversions?

steve · **Posted:** Fri Mar 04, 2011 8:22 am

Vathek wrote:

Ok, what is the difference between the dew point calculated from the station or from cumulus? Are there known differences between the two conversions?

I have no way of knowing; I don't own a La Crosse station, and I don't know what formula they use. Cumulus uses the same formula as Davis weather stations; I can give you the formula if you wish.

Vathek · **Posted:** Fri Mar 04, 2011 3:01 pm

steve wrote:

Vathek wrote:

Ok, what is the difference between the dew point calculated from the station or from cumulus? Are there known differences between the two conversions?

I have no way of knowing; I don't own a La Crosse station, and I don't know what formula they use. Cumulus uses the same formula as Davis weather stations; I can give you the formula if you wish.

No problem steve, I trust you

Stephenwx82 · **Posted:** Sun Mar 06, 2011 12:33 pm

Thanks for that guys, with the spike happening I switched Cumulus over to calculate the DP, if its off Davis stations thats awesome then, I also trust you Steve.

FTDI new drivers for the converter came out and everything with spike removal on seems sweet, maybe I'll remove spike filtering in the next few days and see what it does, my temp scope is similar to your's Vathek unreal

I mean it doesn't matter if the calculation of DP is a good quality one IE Davis but its just an observation of what happened.

Cheers
Stephen

	It is currently Sat May 25, 2013 8:38 am
Please click here before posting. Help me to help you!
Useful Links: Cumulus FAQ • Enhancement requests • Wiki (documentation)
Please put your approximate location into your profile
Add your web site to the Cumulus user map
Vantage Pro2 users with firmware 3.00 should upgrade to fw 3.12 and Cumulus 1.9.4
Latest Cumulus release v1.9.3 (build 1059) - Feb 09 2013 Latest Cumulus beta v1.9.4 build 1078 - May 24 2013 --> Latest Cumulus Realtime v1.0.0.5 - Sep 05 2009

Sandaysoft

La-Crosse WS2300 - Optimal Settings

Who is online